menu
menu
Blog Image 33

Mastitis Control Plan part 2: the crucial role of liners

Among the advised actions to protect your herd from mastitis, ensuring a correctly functioning and fitting liner during milking could be a crucial step. With this in mind, let’s discover what our experts Luiz Cutolo and Ghislain Coppejans suggest for the well-being of your cows. 

As depicted in the previous episode, farmers should follow a solid Mastitis Control Program to prevent dangerous bacteria from entering the teat canal, due to direct contact with contaminated surface, an incorrect milking routine or a malfunctioning system. In the latter case, liners are emblematic, as they are the component directly touching cow udder during milkingConsequently, issues in liner conditions can immediately affect teat health, determining mastitis cases.  

With the help of Luiz and Ghislain, we will discover the relationship between liners and mastitis, as well as some good practice to make the most out of this primary milking component. 

What is the relationship between liners and mastitis? 

Firstly, it is important to distinguish between two main functions of the liner: 

  • During opening phase, it allows vacuum to open the sphincter and milk to flow out of the teat. This happens after a proper stimulation with oxytocin release, activating milk letdown. 
  • During closing phase, liner walls touch each other, with the aim to decongest the teat tissue. With this regard, Luiz underlines“The liner exerts an increasing compression force on teat, until overcoming the diastolic blood pressure, stopping the milk flow and decongesting teat tissue. This action should be extremely gentleto safeguard teat conditions. 

Mastitis infection is, in fact, strongly correlated to serious cases of hyperkeratosisan excessive thickening of the skin around teat external orifice, due to either mechanical stress, caused by over pressure, or liner slippage. 

Moreover, it is important to consider: 

  • Vacuum level. If too highvacuum might limit milk flowcausing excessive teat congestion. Consequently, milking is painful and stressful for cows, which then produce adrenaline, that limits oxytocin releaseIf too low, vacuum does not relieve congestion and lowers the milk flow. Thus, teat opening is hindered while transport capacity reduced, milking time increases, and the process becomes painful for the animals. These become restless and start kicking, causing irregular vacuum variations by sudden air intakes during milking and consequent back flush of milk to teats. This reflux of milk increases infection risk, as it keeps the teat wet. 

  • Overused liners. According to the compound, liners have different life spans. Rubber ones, for instance, should be replaced after 2500 milkings, silicone ones after 5000 milkings, while liners used in the US need to be changed after 1200 milkings, due to a lower carbon black content in the compound. One of the main implications is a bad detachment from teat, causing stress to cows and liner fall-off. Furthermore, when closing to decongest the teat, liner may cause over pressure on the sphincter at each pulsation cycle. As far as worn liners, Ghislain adds: “Overused and worn liners lose their physical properties like tension, barrel shape and normal wall movement, with delayed acceleration. These factors decrease touch point pressure and tension, while over pressure raises. In turn, milk flow slows down, compression forces increase, and the massage action is incorrectBecause of barrel shape deformation, teats do not properly enter liners, which will slip easily and close around the teats with very low decongestion capacity.” 

Liner compression and over pressure 

Liner compression (LC) is the average liner compressive pressure, measured in kPa, applied to internal tissues during massage phase of pulsation cycle. 

LC depends on liner shape, dimensions, material, tension, as well as vacuum level and rest phase duration. Therefore, the key for its control lays in finding the right model fitting and maintaining changeover according to manufacturer’s recommendations. 

Right levels of LC promote fluid removal from teat end tissues, with a consequent faster milk flow during the B-phase. 

When these are not achieved, as in case of overused liners, over pressure (OP) may occur. This is an average liner compressionhigher than the one required to start or stop milk flow during massage phase, which implies an increase in teat end hyperkeratosis, due to an excessive keratin removal from the canal. 

How should the milking unit be removed from the animal? 

Liner removal should follow some stages: 

  • Firstly, vacuum is shut-offby either the cluster valve or the ACR vacuum shut-off one. 
  • Then, the milking unit needs to be aerated, to remove teat end mouthpiece vacuum before pulling the cluster from the udder. 
  • When the barrel is fully aerated, a light pressure is sufficient to remove the liner smoothly.  

In case of Automatic Cluster Removers, finding the right delay between vacuum shut-off and cluster pull-off from the udder can be rather challenging. This delay is programmable according to the type of venting, either claw or mouthpiece, and the liner barrel dimensions. The safest moment to pull the cluster from the udder is when the liner slips from the teat. 

On the contrary, as Ghislain points out: When the system pulls clusters from the udders but the hood vacuum does not drop properly and liners are still stuck to the animal, these will not come off immediately and the removal will be rough, promoting infections. 

Another aspect to remember is that too long cow milking time and overmilking periods will influence teat condition considerably. The overmilking or flow descending phase should be no longer than 30 seconds per quarter. 

In this episode we investigated the relationship between liners and mastitis, clarifying how bad choices in terms of milking components and settings can have extremely negative effects on teat integrity, representing a potential base for the spread of mastitis pathogens. 

In the following episode, instead, we will point out some useful tips in terms of hygiene and safety that will turn liners into your best allies towards mastitis. Don’t miss it! 

milkrite | InterPuls thank Luiz Cutolo and Ghislain Coppejans for their excellent support. 

Sources: 

 

 

Date: 20 July 2021

  • Summary:
    How to control and prepare for Mastitis by getting your liners right!